Router1 ! interface Loopback0 ip address 3.3.3.3 255.255.255.255 ! interface Serial2 ip address 1.1.1.2 255.255.255.0 ! router ospf 1 network 1.1.1.0 0.0.0.255 area 0 !
Router2
Router2 ! interface Loopback0 ip address 2.2.2.2 255.255.255.255 ! interface Serial1/0 ip address 1.1.1.1 255.255.255.0 clockrate 2000000 ! router ospf 1 network 1.1.1.0 0.0.0.255 area 0!
用未编号的接口配置 在此部分，您介绍用信息配置通过未编号的接口连 接和运行OSPF的路由器。
注重： 找到其它信息关于用于本文的命令，使用 命令查找工具 (注册的用户)。
网络图
配置 此部分使用如下所示的配置。
Router1
! interface Loopback0 ip address 3.3.3.3 255.255.255.255 ! interface Serial0 ip unnumbered loopback 0 encapsulation ppp ! router ospf 1 network 3.3.3.0 0.0.0.255 area 0 !
Router2
! interface Loopback0 ip address 2.2.2.2 255.255.255.255 ! interface Serial0 ip unnumbered loopback 0 encapsulation ppp ! router ospf 1 network 2.2.2.0 0.0.0.255 area 0 !
验证 此部分提供您能使用确认您的配置适当地工作的信息。
输出解释器工具 支持 某些show命令 (注册的 用户) ，答应您查看show命令输出分析。
验证用IP地址 下列是在Router1发出的 show ip ospf neighbor 命令的输出。 Router1#show ip ospf neighbor Neighbor ID PRi State Dead Time Address Interface 2.2.2.2 1 FULL/ - 00:00:32 1.1.1.1 Serial 0
得知更多 show ip ospf neighbor命 令，参见 什么执行 show ip ospf neighbor命 令显示？
下列是 show ip ospf interface命令的输出 在Router1。 以下 表示OSPF网络类型为接口Serial0点到点。 Router1#show ip ospf interface serial 0 Serial0 is up, line protocol is up Internet Address 1.1.1.2/24, Area 0 Process ID 1, Router ID 3.3.3.3, Network Type POINT_TO_POINT, Cost: 64 Transmit Delay is 1 sec, State POINT_TO_POINT, Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Hello due in 00:00:05 Index 1/1, flood queue length 0 Next 0x0(0)/0x0(0) Last flood scan length is 1, maximum is 1 Last flood scan time is 0 msec, maximum is 0 msec Neighbor Count is 1, Adjacent neighbor count is 1 Adjacent with neighbor 2.2.2.2 Suppress hello for 0 neighbor(s)
同样地，输出为 show命令在Router2如下所示。 Router2#show ip ospf neighbor Neighbor ID Pri State Dead Time Address Interface 3.3.3.3 1 FULL/ - 00:00:32 1.1.1.2 Serial0 Router2#show ip ospf interface serial 0 Serial0 is up, line protocol is up Internet Address 1.1.1.1/24, Area 0 Process ID 1, Router ID 2.2.2.2, Network Type POINT_TO_POINT, Cost: 64 Transmit Delay is 1 sec, State POINT_TO_POINT, Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Hello due in 00:00:05 Index 1/1, flood queue length 0 Next 0x0(0)/0x0(0) Last flood scan length is 1, maximum is 1 Last flood scan time is 0 msec, maximum is 0 msec Neighbor Count is 1, Adjacent neighbor count is 1 Adjacent with neighbor 3.3.3.3 Suppress hello for 0 neighbor(s)
验证与未编号的接口 show ip ospf nei ghbor 命令在Router1和Router2确认完全邻接。以下表示 OSPF网络类型为接口Serial0点到点。
得知更多 show ip ospf neighbor命 令，参见 什么执行 show ip ospf neighbor命 令显示？ Router1#show ip ospf neighbor Neighbor ID Pri State Dead Time Address Interface 2.2.2.2 1 FULL/ - 00:00:37 2.2.2.2 Serial0 Router1#show ip ospf interface serial 0 Serial0 is up, line protocol is up Internet Address 0.0.0.0/0, Area 0 Process ID 1, Router ID 3.3.3.3, Network Type POINT_TO_POINT, Cost: 64 Transmit Delay is 1 sec, State POINT_TO_POINT, Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Hello due in 00:00:08 Index 2/2, flood queue length 0 Next 0x0(0)/0x0(0) Last flood scan length is 1, maximum is 1 Last flood scan time is 0 msec, maximum is 0 msec Neighbor Count is 1, Adjacent neighbor count is 1 Adjacent with neighbor 2.2.2.2 Suppress hello for 0 neighbor(s)
同样地，输出为 show命令在Router2如下 所示。 Router2#show ip ospf neighbor Neighbor ID Pri State Dead Time Address Interface 3.3.3.3 1 FULL/ - 00:00:30 3.3.3.3 Serial0 Router2#show ip ospf interface serial 0 Serial0 is up, line protocol is up Internet Address 0.0.0.0/0, Area 0 Process ID 1, Router ID 2.2.2.2, Network Type POINT_TO_POINT, Cost: 64 Transmit Delay is 1 sec, State POINT_TO_POINT, Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Hello due in 00:00:08 Index 2/2, flood queue length 0 Next 0x0(0)/0x0(0) Last flood scan length is 1, maximum is 1 Last flood scan time is 0 msec, maximum is 0 msec Neighbor Count is 1, Adjacent neighbor count is 1 Adjacent with neighbor 3.3.3.3 Suppress hello for 0 neighbor(s)
